DIY

DIY Ziploc Bag Organizer

I’m Zoe.
My mission is to teach you to  confidently build magazine-worthy DIYs. I used to be terrified of power tools, which is why I'm a firm believer that ANYONE can DIY.
Get The Getting Started Guide
Gimme that

Not to be dramatic, but there’s nothing more annoying than a messy, disorganized drawer. We decided to build a DIY Ziploc bag organizer to make one of our drawers a little less disheveled. 

The organizer helps keep everything in place and organized. It also lets you throw away the branded cardboard storage boxes and have a cleaner and more cohesive look. 

before and after of drawer with Ziploc bag organizer

This DIY Ziploc organizer fits an entire Costco variety pack of Ziploc bags: 52 gallon bags, 50 quart, 125 sandwich, and 120 snack. 

Note: we have not tried this organizer with bags that have sliders instead of zippers.

Yes, you can buy Ziploc bag organizers online for a somewhat reasonable price, but we already had scrap wood laying around, making ours free. And free is my favorite price to pay!

If you don’t have scrap wood laying around, you can make one for the price of a 2×4 sheet of plywood, which is still about 50% cheaper than buying one of the cheaper options

Before you build your own, measure your drawer to make sure that the inside is at least 13” wide and 3.5” deep. 

The final dimensions of this DIY Ziploc bag organizer is 13x13x3.5. 

Recommended Tools: 

  • Circular Saw
  • Drill 
  • Jigsaw 
  • Brad Nailer

What you’ll need:

Cut List: 

For?Board SizeQuantitySize (inches)
Bottom½” plywood113×13
Top½” plywood113×13
Sides½” plywood213×2.5
Front/Back½” plywood212×2.5
Long Divider½” plywood112×2.5
Short Dividers½” plywood27.75×2.5

How to Make a Wooden Ziploc Organizer

New to DIY? Download our free 5 Steps to Getting Start with DIY guide!

STEP 1: MAKE YOUR CUTS

We made our entire Ziploc organizer out of a 2’x4’ sheet of maple plywood. Cut your plywood down to sizes you need according to the cut list above. 

We used our circular saw and Kreg rip cut guide to cut everything down, but you could also use a table saw.

STEP 2: CUT HOLES FOR ZIPLOC BAGS

Now that we have the main pieces cut, it’s time to cut the holes for the Ziploc bag compartments. This is the most tedious part of the project, but you’ve got it! 

Grab your top piece and start sketching out where you want to cut. Each of the compartments will be approximately 2.5” wide. 

For the top compartment, it is 2” in from either side and 1.25” down from the top. I set my multi-mark tool at 3.75” to mark the bottom of the top compartment. 

drawing where to cutout using Kreg mulit-mark tool

The remaining (3) compartments are each 6×2.5”. They are 1 1/8” from the bottom and 1.5” from either side. Between compartments, there is a 1.25” gap. 

sketches of where to cut compartments for Ziploc bag organizer

Now that it’s all marked, it’s time to cut them out…almost. I wanted rounded corners on my compartments and I’m going to use my drill to accomplish this. 

Before I start drilling, I want to mark exactly where to drill. I used a 3/8” drill bit, so I went ahead and marked 3/16” in from the corners of my compartments. 

But, I didn’t just mark directly on my wood. I first placed painter’s tape on the corners to help prevent the wood from tearout as I drill through. 

marking 3/16" with Kreg multi-mark tool

Once everything is marked, now it’s time to drill. Line the tip of your ⅜” drill bit up with one of the marks that you made, and drill on through. 

Then repeat with the remaining 15 holes. 

drilling through tape with 3/8" drill bit

Once my holes were drilled, I grabbed my multi-mark tool and connected the space between my holes. For the most part, things lined up with the lines that I previously drew. However, there were one or two spots where my holes did get a little of out alignment. 

connected two drilled holes using Kreg multi-mark tool

Now it’s finally time to actually start cutting. 

Insert your jigsaw into one of the holes that you drilled and connect the dots. Repeat this until all four compartments are cut out. 

cutting out holes for Ziploc bag organizer using a jigsaw

STEP 3: ASSEMBLE USING GLUE AND NAILS

Phew, now that you’ve powered through step 2, it’s time to assemble! 

Note: if your holes are a little rough, it’ll be easier to sand the inside of the holes you cut before assembly. 

To assemble, we’ll use wood glue and 1” nails. You’ll place each piece on top of the bottom and nail through the bottom and into the new piece. 

You can also forgo the nails and just glue and clamp everything in place if you prefer. 

First, attach the sides to the bottom. The sides should be flush with the sides and top/bottom of the bottom piece.

placing sides on the back

Then attach the back to the bottom, placing it between the two sides and flush with the edge of the bottom. 

nailing back to the bottom piece

Next, we will build the dividers for the Ziploc bag storage using the front piece, the long divider, and the short dividers. 

The short dividers should be placed approximately 3 5/8” from each other and from either end of the long divider/front pieces. Nail through the front piece and into the short dividers. Then nail through the long divider and into the short dividers. I added 2-3 nails to each side of each divider. 

overhead shot of bag organizer before installing

Now you can install the divider onto the bottom piece and between the two sides. Rather than trying to nail the dividers through the back, I relied on wood glue and just clamped it in place for about 30 minutes.

clamping organizer to plywood

Finally, attach the top to the rest of the Ziploc bag organizer. 

nailing top of organizer to rest of structure

If everything doesn’t line up perfectly, it’s okay. It’s just a box that goes in a drawer. You’ll really only ever seen the top and maybe one side of it!

STEP 3: PREP FOR STAIN OR PAINT

Now that everything is assembled, it’s time to finish it up! We first filled all of the nail holes using a stainable wood filler

Then we sanded it using 120, 180, and 220 grit sandpaper. Be careful not to sand for too long, or you might sand through the plywood veneer! 

STEP 4: STAIN OR PAINT

The remaining steps are all completely optional. You can finish your Ziploc bag organizer however your heart desires. You can use paint or stain or leave it as natural wood. 

We opted to finish ours with Minwax Solid Stain in Gentle Olive. It’s the 2022 Color of the Year!

staining using Minwax Gentle Olive solid stain

STEP 5: ADD LABELS

We used our Cricut Maker to cut out the labels. I was going to tell you what font and size we used, but unfortunately, the file didn’t save… 

What I can tell you is that the letters are approximately 3/8” tall. 

STEP 6: SEAL WITH POLYCRYLIC

The final step in this project is to seal it all with Polycrylic. I opted for the spray Polycrcylic for quick and easy application. I applied three coats of the matte sheen. 

DIY Ziploc bag organizer standing up to be sprayed with Minwax Polycrylic in Clear Matte

If you opted to paint, you can skip this step. 

STEP 7: ADD YOUR ZIPLOC BAGS

Once your Ziploc organizer is dry, you can insert your bags! To do that, you’ll just insert them through the top. 

There you have it! Now you have your very own Ziploc bag organizer! This DIY project can be knocked out in just a few hours.

DIY Ziploc Bag Organizer finished with green stain and vinyl labels

The vast majority of my time of the project was spent figuring out the exact dimensions and placement of the compartments. Since I gave that to you, it shouldn’t take too long at all. 

If you’re looking for more kitchen organization ideas, check out this post on measuring cup organization. I like this method SO much more than storing them in a drawer. 

Add a comment
+ show Comments
- Hide Comments

Leave a Reply

Your email address will not be published.

Join the List

Our mission: give you the resources to build magazine-worthy furniture.

First up? Sharing the 5 key steps to getting started with DIY.

 Get  the best DIY tutorials, project inspiration, and  DIY tips sent straight to your inbox weekly.

Get My Getting Started with DIY Guide as a free gift!

Find your next project

Premium, printable plans

3D renderings, detailed shopping lists, cut lists displayed two ways (both in chart form and visually), AND a bonus SketchUp file. Printable plans don't get better than this.

See the plans
diy with confidence

Our Courses

Whether you're just getting started or you're a seasoned DIYer who's ready to unlock the full potential of DIY, our courses are here to help.

SEE OUR COURSES

Instagram

Join us for project tutorials, behind-the-scenes, and quick DIY tips and tricks.

@pineandpoplardiy_