DIY

The Easiest DIY Bath Tray With Just One Board!

I’m Zoe.
My mission is to teach you to  confidently build magazine-worthy DIYs. I used to be terrified of power tools, which is why I'm a firm believer that ANYONE can DIY.
Get The Getting Started Guide
Gimme that

If you’re a bath lover like me, you understand the importance of a bath tray. 

A few years ago, we made a DIY bath tray with all the bells and whistles ( a book holder, candle holder, wine glass holder), but it doesn’t fit the new bathtub. 

Easy DIY Bath tray made from poplar wood sitting on white bath tub

So this time we decided to go for clean, simple, and modern. This is the easiest DIY bath tray tutorial, so let’s dive right in. 

Recommended Tools: 

What You’ll Need: 

  • (1) – 1x6x8 board (we used poplar with a really fun grain pattern) 
  • Wood glue 
  • 1.25” nails 
  • Sealer (we used water-based Helmsman spar urethane in clear satin)

How to Make a Wooden Bath Tray 

New to DIY? Download our free 5 Steps to Getting Start with DIY guide!

STEP 1: MEASURE YOUR TUB 

Measure the overall width of your tub. Then measure the thickness of your tub. 

measuring width of bath tub with tape measure

STEP 2: CUT YOUR WOOD 

Cut your wood to match the overall external width of your tub. You can cut it to be slightly smaller if you want to ensure the bath tray doesn’t extend past the edge of the tub. 

As you’re cutting, consider the grain pattern. Since this is such a simple tray, the wood itself is really the star of the show. Consider which pieces of the board you want to include in your tray before cutting. For me, there was a knot that I really wanted to make sure I included.

poplar wood laid on ground to determine grain pattern

Then cut two pieces to approximately 1” wide. These two pieces don’t need to be exact. 

STEP 3: SAND 

Sand your wood with 120, 180, and 220-grit sandpaper so that it’s nice and smooth. 

STEP 4: SEAL 

If you want to stain your wood, you can certainly do that. We loved the natural look of the poplar wood, so we decided to skip the stain on this project.

We chose Helmsman’s Spar Urethane because it’s great for projects that will be exposed to water. Spar Urethane was the go-to sealer for boats, so I trust it for my little bath tray! 

As you’re buying your sealer, make sure to grab the water-based version. This will not yellow or amber. If you want to add a little more color to your piece, you can opt for the oil-based version that will add some yellow/amber to your wood color. 

We applied three coats of sealer, following the instructions on the can for dry times. Once dry, we lightly sanded with 220-grit sandpaper between each coat.

STEP 5: ASSEMBLE 

Once dry, it’s time to assemble! I like to place a towel underneath my wood at this step to prevent my workbench (and all the glue that’s stuck on it over time) from scratching my wood. 

For this bath tray, we opted for a slight gap between the two boards. You can keep the gap or push the boards together completely. 

Grab your 1” pieces and center them up from side to side (the distance will depend on how big your gap is, which is why I’m not providing measurements). 

using Kreg multi-mark tool to measure setback of support boards

Then place them however far in they need to be for your particular tub.

You want to place the boards slightly further in than the thickness of the tub so that the tray can slide and move easily. I’d recommend an additional 1/4” – 1” on each side depending on how much you want it to be able to move. 

Once you’re happy with the placement, you can add some tape around your 1” piece to mark the placement. 

gluing wood

Then add some wood glue to the bottom of the pieces and position it on the bath tray. Add 4 nails to each 1” piece, making sure to avoid the gap in the middle!

nailing 1" board to bottom of bath tray

Note: wood glue works best on unsealed surfaces. You can either wait to seal the bottom until after assembly or you can mark where the board will go and avoid sealing those exact spots for maximum adhesion. 

And if you’re wondering why I recommended sealing before assembly, it’s so that I could seal the edges that will have a small gap between them. There’s no way my paintbrush would’ve fit after assembly! 

simple wood bath tray sitting on freestanding tub

There you have it! Now you know how to build the world’s easiest DIY bath tray! Well actually, I can think of one that would have been even easier…using just one piece of wood instead of having two with a gap! 

The easiest DIY bath tray text overlay on image of simple wood bath tray
DIY simple wood bath tray sitting on white freestanding tub
Add a comment
+ show Comments
- Hide Comments

Leave a Reply

Your email address will not be published.

Join the List

Our mission: give you the resources to build magazine-worthy furniture.

First up? Sharing the 5 key steps to getting started with DIY.

 Get  the best DIY tutorials, project inspiration, and  DIY tips sent straight to your inbox weekly.

Get My Getting Started with DIY Guide as a free gift!

Find your next project

Premium, printable plans

3D renderings, detailed shopping lists, cut lists displayed two ways (both in chart form and visually), AND a bonus SketchUp file. Printable plans don't get better than this.

See the plans
diy with confidence

Our Courses

Whether you're just getting started or you're a seasoned DIYer who's ready to unlock the full potential of DIY, our courses are here to help.

SEE OUR COURSES

Instagram

Join us for project tutorials, behind-the-scenes, and quick DIY tips and tricks.

@pineandpoplardiy_