Barnwood and aged wood add so much character to a project, but it can be pricey and more difficult to get your hands on than simply swinging by Home Depot. We had some scrap 2x4s and 2×2 furring strips in our garage and decided to try out a new technique on them.
Rather than try to make them look newer, what if we distressed the wood and tried to make it look old? We wanted to add some character to the whitewood, but we didn’t want to rely on staining or painting techniques.
We wanted to add texture. We wanted to distress the wood and add dents and dings so that it looked like it had a story to tell. It turned out better than expected!
Without further ado, let’s start DIYing and learn how to make new wood look old.
This post contains affiliate links for your convenience (which means if you make a purchase after clicking a link, I earn a teeny-tiny commission, but it won’t cost you a penny more)! Click here to read our full disclosure.
What you’ll need:
- Wire brush drill attachments (we used the cup brush in this kit to clean our garage floors)
- Screws or nails (any size)
- An old sock
- Optional: hammer
- 120 grit sandpaper
- 220 grit sanding block
How to Make New Wood Look Old
Wish you could build magazine-worthy furniture and decor without a workshop full of expensive tools? Get the Essential Tools Roadmap and find out which tools are essential to DIY and which 3 tools you should start with.
STEP 1: SAND YOUR WOOD
Before we begin distressing the wood too much, we want to sand it with 120-180 grit sandpaper. We won’t be sanding too much after distressing the wood, so we want to knock out the majority of the sanding first.
Sanding will help prepare the wood to more evenly accept stain. It also helps knock off some of the yellow if you’re working with pine.
STEP 2: DISTRESS THE WOOD USING A WIRE BRUSH
This is the secret to making new wood look old and reclaimed. We’re going to weather it by adding a lot of texture.
Insert a wire brush attachment into your drill and press the drill trigger to get it spinning.
Run the wire brush along the surface of the wood, moving in the same direction as the wood grain. You can apply more pressure to certain areas if you want to add some deeper grooves and texture.
If you want to add some more scratches or variation, you can use the cup brush attachment in a few areas as well. You can even lightly run the brush in the direction opposite of your wood grain to give it some scratches across the surface.
STEP 3: ADD MORE DENTS AND DINGS
Before you dive into this part, I’d recommend trying out one or both of the methods on a piece of scrap wood to see if you like them.
If you want to add some more dents and dings to your wood to give it even more of a reclaimed look, there are two main things you can do.
The first is to hit it with a hammer. You can hit with either the normal hammer end or you can hit it with the side that is used to help pull out nails.
The second option is to put a handful of screws or nails into an old sock. Then hold the end of the sock so that it’s closed up and hit the sock onto the wood in various places.
We’ve tried this method with bags and other materials, but I highly recommend the sock. The sock offers enough support that the nails/screws don’t fly out or break the sock, but it still has enough give where the nails/screws can poke into the wood.
When making our bath stool, we just used the screws in the sock method to add a little more character. We hit the top of the stool about 5 times.
STEP 4: SAND WITH 220-GRIT SANDPAPER
Now that you’re happy with the amount of distressing that you’ve done to your wood, let’s prep it for stain! Grab a 220-grit sanding block and sand your wood.
The goal here is not to remove the texture, but to remove the splinters and some of the “fuzzy” spots that the wire brush left behind.
STEP 5: WIPE OFF YOUR SURFACE
Using either a clean rag or a shop vac, clean off any lingering dust that might be on your wood. There will be a lot more than a normal, new piece of wood because of all of the texture.
STEP 5: APPLY A FINISH
Now that you’ve distressed your wood to make it look old, it’s time to add the finish of your choice! For our bath stool, we finished it with Minwax Semi-Transparent Stain in Driftwood.
Warning: because of the texture added, your wood will absorb more stain (aka stain darker) than a normal piece of wood. Make sure to distress a piece of scrap wood and test your stain colors on it before finishing your project!
You can use any finishing option that you would use on a new piece of wood, but you might want to adjust how you apply it. If you usually use a foam brush, I would recommend a different paintbrush or a clean rag. All of the texture might catch and ruin the foam brush.
If you are staining oak and want an even more weathered, aged look, I would recommend Minwax Wood Effects. They have both a weathered gray and charred black option.
The reason I specify that this is an option if you’re staining oak is because the Wood Effects reacts with tannins in the wood to create an aged look. It literally changes before your eyes over about an hour.
However, wood like pine does not have enough tannins in the wood to cause a reaction. If you’re working with pine, traditional stain or another finishing option will be better.
Speaking of other finishing options, there are several combinations that are known to give an aged wood look. You can try a combination of tea, coffee, and paint to get your desired look.
Or you can let some steel wool soak overnight in some white vinegar. The next day, you can dilute the vinegar with water using a 1:1 ratio and use that mixture to stain your wood.
The options are really limitless!
The ONLY tools you need to DIY
Want to build magazine-worthy furniture and decor? The Essential Tools Roadmap will show you what tools you actually need to complete 95% of DIY furniture and home improvement projects (it’s not as many as you think!).
Frequently Asked Questions
Can you dust the wood?
It depends. It depends on what you’re using to dust it and how you ended up sealing it.
If you’re trying to use a Swiffer duster, it doesn’t work all that well because the duster will eventually get caught on some of the texture.
But if you want to wipe it with a clean rag, then yes, you can easily dust it and wipe it down! Our dalmatian is constantly shedding and her fur has wiped right off.
Since we sanded it down before finishing it, I can even wipe it off with my hand. You can feel the texture, but I have yet to get a splinter.
We haven’t had it long enough to tell you if the texture gathers dust, but I would think that it would take a long time for it to be noticeable.
Any other questions? Pop them in the comments below this post.
We can’t wait to see what projects you finish with this technique! Cheers to making new wood look old (and distressed)!